2017 August New 300-165 Exam Dumps with PDF and VCE Free Updated Today! Following are some new 300-165 Questions:

1.|2017 New 300-165 Exam Dumps (PDF & VCE) 174Q&As Download:
https://www.braindump2go.com/300-165.html

2.|2017 New 300-165 Exam Questions and Answers Download:
https://drive.google.com/drive/folders/0B75b5xYLjSSNRU9xWGk1cFJiaTg?usp=sharing

QUESTION 94
Which task must be done before a zone set takes effect?

A.    Add a member to the zone.
B.    Enter the exit config t command.
C.    Enter the copy running-config startup-config command.
D.    Enter the zoneset activate name <zone-name> vsan <vsan-#> command.

Answer: D

QUESTION 95
Which parameter is configurable when setting up logging on the Connectivity Management Processor?

A.    the number of CMP messages to save in a single log file
B.    the number of times the log can roll over
C.    the directory to save the log file to
D.    the severity threshold of the messages to log

Answer: D

QUESTION 96
Which statement describes what happens if a new EPLD version is released with a new Cisco NX-OS version for a Cisco Nexus switch, but these EPLDs are not upgraded at the same time that NX-OS is upgraded?

A.    Any new hardware or software feature that depends on the updated EPLD image is disabled until upgraded.
B.    Modules that use an updated EPLD image remain offline until the EPLD is upgraded.
C.    The EPLD image version mismatch is detected by the supervisor, which automatically initiates an upgrade.
D.    The Cisco NX-OS upgrade fails as a result of the mismatch between EPLDs and NX-OS versions.

Answer: A

QUESTION 97
Which two options are limitations of NetFlow Version 5? (Choose two.)

A.    no support for IPv6, Layer 2, or MPLS fields
B.    fixed field specifications
C.    excessive network utilization
D.    analyzes all packets on the interface

Answer: AB

QUESTION 98
In Cisco Nexus 7000 Series Switches, which three statements about SPAN are true? (Choose three.)

A.    SPAN source ports can be the in-band interface to the supervisor engine control plane of the switch.
B.    SPAN monitor ports can be routed ports.
C.    SPAN destination ports can be configured in only one SPAN session at a time.
D.    The Cisco Nexus 7000 supports virtual SPAN feature.
E.    SPAN destination port actively participates in spanning-tree instance.
F.    SPAN destinations cannot be an RSPAN VLAN.

Answer: ACD

QUESTION 100
Which three options are CallHome predefined destination profiles that are supported on Cisco NX-OS? (Choose three.)

A.    CiscoTAC-1
B.    full-text-destination
C.    pager-xml-destination
D.    short-text-destination
E.    xml-text-destination
F.    pager-json-destination

Answer: ABD

QUESTION 101
If you are using NAT in your data center, which load balancing would you be likely to use within your GLBP configuration?

A.    none
B.    round-robin
C.    host dependent
D.    weighted

Answer: C

QUESTION 102
Which command specifies a load-balancing method based on the MAC address of a host where the same forwarder is always used for a particular host while the number of GLBP group members remains unchanged?

A.    load-balancing host-dependent
B.    load-balancing mac-pinning
C.    load-balancing round-robin
D.    load-balancing weighted

Answer: A

QUESTION 103
Which feature allows routing protocols to remain in the data path during a supervisor failover?

A.    Cisco Nonstop Forwarding
B.    Cisco Stateful Switchover
C.    Cisco Express Forwarding
D.    Cisco Route Processor Redundancy

Answer: A

QUESTION 104
Which two functions are enabled when you set up vPC+ at the FabricPath edge? (Choose two.)

A.    the ability to attach Cisco Fabric Extenders in FEX active/active mode
B.    the ability to stop all Layer 3 egress traffic
C.    the ability to attach servers to edge switches with port-channel teaming
D.    the ability to attach additional Classic Ethernet switches in vPC+ mode

Answer: AC

QUESTION 105
How does addition of bandwidth between spine and leaf switches in a FabricPath architecture get utilized?

A.    Links between the same set of switches are automatically added to a port channel.
B.    Adding additional bandwidth is handled dynamically using the 802.1AX protocol.
C.    Traffic is load shared automatically across the available paths to the destination.
D.    FabricPath uses hardware bonding of physical interfaces to form higher-speed links.

Answer: C


!!!RECOMMEND!!!

1.|2017 New 300-165 Exam Dumps (PDF & VCE) 174Q&As Download:
https://www.braindump2go.com/300-165.html

2.|2017 New 300-165 Study Guide Video:

https://youtu.be/IyG8YCqJDdc